New Products for May 2017

New Products for May 2017
April 17, 2017 Coleman Mcvea

1991-1992 FJ80 Extended Brake Line Kit

Our DOT approved FJ80 Land Cruiser Extended Brake Line Kits are suitable for all 1991-1992 FJ80 Land Cruisers with up to 4″ [102mm] of lift. These brake lines are constructed from extruded PTFE (Teflon™) hose with permanently crimped zinc-plated steel fittings. The brake hose is protected from debris and abrasion by a braided stainless steel wire cover. A clear PVC outer jacket provides additional protection against debris, abrasion, and corrosion.

These extended brake lines are a direct fit and exceed all requirements of the Department of Transportation Motor Vehicle Standard MVSS-106. They come in a complete set of one front brake line and one rear brake line along with two retention clips and installation instructions.

Will Not Fit 1993+ FJ80

1988-1995 Toyota Pickup | 1988-1995 4Runner | Auto w/chain T-case, Manual with 3.0L V6 Transmission Mount

If your 88-95 Toyota Pickup or 4Runner has a chain driven T-case, this is the correct Transmission mount.

This is an aftermarket replacement that costs just a fraction of the OEM part from Toyota.

FITS: 1986-1995 with Chain Driven t-case. Either with 22RE Auto w/chain or 3.0L V6 with Manual Trans.

2016-Present Toyota Tacoma “HoneyBadger” Front Bumper by Addictive Desert Designs

Specifically designed for the Toyota Tacoma, the HoneyBadger front bumper is one of the toughest and most aggressive bumpers you can buy. Made with 1/8″ external steel plating and removable 1/8″ aluminum accent panels.

With an aggressive style the HoneyBadger front bumper for the Toyota Tacoma gives your truck a tough look, while providing superior protection to your front end components. Reinforced clevis mounts made from 1″ steel are designed to accommodate a 3/4″ D-ring.

Our universal light mount system in the center of the bumper allows for up to 8 Duallys or a 30″ Straight or Radius LED bar to be mounted. Mix and match any brand and size lights with the universal light kit to create the perfect lighting combination for your needs. Additional lighting options are available behind the side accent panels, accepting a Rigid Industries 10″ LED on each side.

1986-1995 Suzuki Samurai Replacement Targa Bar Parts

A damaged targa bar can cause a lot of headache. With a bent Targa you may have trouble closing doors or getting your soft top on. Even your windshield will be affected by a badly bent Targa Bar.

Low Range Off-Road stocks each part needed to replace a Samurai Targa Bar.

  • Left and Right B-pillar Sides
  • Center Arch over the top
  • Left and Right Windshield Attachment Bars which sit above the doors.

New bolts are available and recomended for each component.

These are genuine Suzuki parts in gray primer.

Trail-Creeper™ Tacoma Chain Drive Crawl Box

Transfer cases are made from two basic sections; the reduction section and the 4WD section. To build a dual transfer case, two reduction boxes are bolted back-to-back with a dual case adapter. These two are then bolted to a 4WD section. Using the Tacoma-specific adapters, this crawl box is ready to bolt onto the front of a Tacoma chain drive transfer case. In addition, this kit also comes with the necessary adapter and hardware to bolt a dual case to the back of your Tacoma transmission. Units are completely rebuilt and inspected. Low range gear ratio is 4.70. Floorboard and drive shaft modifications are required for dual transfer case installation. No core charge. One year warranty.

Ready to bolt onto the front of a Tacoma Chain Drive Transfer Case

**ALL HARDWARE REQUIRED FOR INSTALLATION IS INCLUDED**

Available options:

  • 304424-1-KIT – 2.7L Auto/3.4L Manual & Auto, 1995-2004
  • 304425-1-KIT – 2.7L Manual, 1995-2004

2016-Present Toyota Tacoma APEX Sliders by All-Pro Off-Road (2016T-AP-APEX)

All-Pro Off Road has done it again! They have been a innovator in developing products for the 05+ Tacomas, and that didn’t stop with the addition of the 2016 models. Rock sliders must be strong to protect your truck, as well as provide the optimal amount of ground clearance. The rocker panels are one of the most vulnerable areas of your vehicle, rocksliders provide you with the protection you need!

All-Pro’s Rock Sliders have been trail tested on some of the most grueling trails around, from the Rubicon to the Hammers and Moab. They are built from USA produced heavy-duty .120″ wall tubing. The shape of the outer tube is very critical and determines how much body protection it will provide as well as how the truck slides along the obstacles without getting hung up. The outer tubes of the Tacoma Rock Sliders are 1.75″ diameter, and angle upward to provide more ground clearance and door protection. The rear of our Rock Sliders extend outward just before the rear wheels to provide extra bodyprotection where it is needed most.

2001-2004 Toyota Tacoma Front MX Grille by Grillcraft

Features

  • 14 Gauge Mesh
  • Welded Mounting Tabs
  • CNC formed
  • Powder Coated Finish

Factor 55 Flatlink E – Grey

The FlatLink E (Expert) is a variation of our popular foldable standard FlatLink winch shackle mount.  The FlatLink E provides a means to eliminate the conventional  winch hook and replace it with a safer and more secure screw pin shackle resulting in a CLOSED SYSTEM WINCHING operation.  The large pear shaped shackle mounting hole allows for attachment to either the pin or bow end of common screw pin shackles, as well as common OEM recovery points. This makes the new FlatLink E more versatile than the current FlatLink design, but it also adds the possibility of a dangerous shackle side loading condition (See Picture), especially during momentary slack conditions. A shackle side loading condition is not possible with our standard FlatLink shackle mount due to the shackle pin mounting constraint. For the recreational off roader we highly recommend the safer standard FlatLink product, not the FlatLink E. This way the winch operator does not have to monitor whether the shackle may have shifted and rotated in the recovery tackle. The FlatLink E is only available in the Military Specification Anodizing (Mil-A-8625 F Type III) hard anodized gray finish.

5 Gallon Metal Jerry Can by Midwest Can Company

Classic Metal “Jerry” gas can fitted with Midwest Can Company’s “Spill-Proof” spout that exceeds California Air Resource Board (CARB) and EPA requirements for portable fuel containers. Shuts off automatically when tank is full. Prevents leakage and spill. Virtually eliminates evaporative emmissions. Made from heavy gauge steel. Red. 5 gallon capacity.

Unit Dimensions:   13.5″ x 6.5″ x 18.25″

Toyota Gear Drive T- Case “Push N Turn” Shifter Base Kit by Marlin Crawler

Marlin Crawler is happy to bring back their USA-made Gear Drive Transfer Case Top Shift Base Kit!

Not only did they bring back an old product, but they have also redesigned many aspects of this kit making it even better than the original.

0 Comments

Leave a reply

Your email address will not be published. Required fields are marked *

*