New Products for March 2017

New Products for March 2017
February 28, 2017 Coleman Mcvea

2016-Present Toyota Tacoma Bilstein 6112 Series Front Adjustable Shocks 0-2.0″ Lift (46-234413) BILSTEIN 6112 Series 

Designed for the serious off-road adventure seeker, the all-new BILSTEIN 6112 Series is the ultimate suspension solution. The 6112 Series optimizes off-road and on-road capabilities with a 60mm digressive piston for increased damping control. This kit features an adjustable spring seat which allows vehicle leveling, larger tires, and increased ground clearance. Kit includes (2) front 60mm shocks, (2) spring seats and (2) springs.

1979-1985 Toyota Pickup | Ultimate Strength Aisin Toyota Solid Axle Locking Hub with Chromoly Hub Gears

Aisin Locking Hubs have long been the gold standard for strength.  Low Range Off-Road has taken the proven design of the Aisin hub and pushed it further. We know the frustration of a breaking a locking hub on the trail and want to prevent you from losing four-wheel drive when you need it the most.

We start with new genuine Aisin locking hubs.  No used or re-manufactured parts.  By replacing the stock gears with 4340 chromoly inners and outers we are offering the strongest hub you can find off-the-shelf anywhere.

Available for purchase in single or pairs.  Replace both sides and save.

1998-2017 Suzuki Jimny Chain Drive T-Case Reduction Gears by Trail-Gear

Trail-Gear is proud to introduce our first set of low range gears for Jimny chain-drive transfer cases. Our Jimny low-range gears will reduce the high-range ratio of your push-button transfer case by 17% and the low-range ratio by 87%. They will greatly improve your off-road experience on Jimnys with a tire size of 29″ [736mm] or higher.

This complete kit includes (4) new gears made from high-strength SCM415 alloy steel and a new speedo gear to correct your speedometer. We also include a set of our Trail-Safe™ Jimny transfer case Input/Output seals along with (3) new staking nuts and a tube of Ultra Grey RTV silicone to seal your transfer case. Detailed instructions are provided to guide you through the installation. Minor clearancing of the transfer case housing required (refer to installation instructions).

Toyota IFS Hub Bearing Dust Cover Cap by Toyota

These dust covers are the first line of defence for your wheel bearings from getting full of dust, water, and rocks. Many people run wheels with out a center cap exposing this cap for the whole world to see. Many people find that over time they become rusty, dented, and even falling off.

Low Range is proud to provide your replacement. Weather you want to replace them because of that huge dent, ugly rust or simply replacing your wheel bearings we provide the replacement you need.

1986-1993 Suzuki Samurai Front Brake Caliper Rebuild Kit

Replacement brake calipers for the Samurai are not particularly expensive.  If your brakes need maintenance we recommend our loaded caliper set. That said, many Do-it-yourselfers have asked for the rebuild parts to freshen up their own existing calipers.

These caliper piston seals are genuine Suzuki replacement parts.

One kit services one side only.

Toyota Tire Pressure Monitoring System (TPMS) by Denso

Denso TPMS Sensors are direct plug-and-play with no programming or cloning needed – they’re built to the specified vehicle right out of the box. With Denso, installation is a snap – the TPMS Sensor relearns just like an OE part, restoring the vehicle to its original condition.


2016-Present Toyota Tacoma

Part Numbers

  • Denso 550-0106
  • 42607-06030
  • 42607-48010
  • 42607-0E020
  • 42607-48010

Suzuki Samurai 1.3L ARP Head Stud Kit

Pro series cylinder head studs from ARP are cold-forged to ensure molecular integrity. They are heat-treated prior to thread rolling and machining and are rated at a whopping 220,000 psi. ARP Pro series kits are also available with 12-point nuts, and all kits come complete with hardened parallel washers for an even load distribution and accurate torque readings.

2010-Present Toyota 4Runner Old Man Emu Suspension Lift Kit – Light Load 3″

Take the the guess work out of ordering your Old Man Emu customized suspension system by ordering this complete kit with a single part number. This complete Old Man Emu suspension kit is designed to accommodate the additional weight of an aftermarket front bumper and winch, as well as the weight of a rear bumper and all your camping gear. This kit achieves approximately 2.5 – 3″ of lift. If you do not have any additional weight on your vehicle, this suspension will be extremely stiff with a much firmer ride than intended.


Leave a reply

Your email address will not be published. Required fields are marked *